The Maxa Beam Basic Package is an entry-level system featuring a 12,000,000 CandlePower Maxa Beam Searchlight. The Basic Package also includes one LiFePO4 battery, AC charger, and an 8 inch power cord.
The Maxa Beam Searchlight features three beam intensity levels and a motorized beam width adjustment that allows the user to vary the beam from a 1° spot to a 40° flood with the press of a button. The system’s LiFePO4 battery powers the light for 115 minutes on regular beam level and recharges in just 110 minutes.
4/2006 – Searchlight output increased from 6,000,000 CandlePower to 7,500,000 CandlePower (G3-12).
1/2010 – Searchlight updated to add control connector (G3-12R).
2/25/2011 – Battery updated from MBP-1207 NiCad to MBP-1310 LiFePO4 Battery Technology.
3/2011 – Output increased from 7,500,000 CandlePower to 12,000,000 CandlePower (G3-20).
6/2013 – Searchlight front lens upgraded to Spyder Lens (G3-20Y).
8/25/2014 – Battery updated from MBP-1310 to MBP-1308 LiFePO4 Battery
5/2016 – Searchlight continuous high beam function added (G3-26).
6/1/2018 – Charger updated from MBP-3205/MBP-3230 to new MBP-3200-AD Multi-Voltage Smart Charger. Battery Fuel Gauge upgrade option released (FG).
Set-Up and Operation
Locate searchlight, battery and power cable.
Attach Searchlight to Battery by lining up the four feet of the searchlight over holes in top of battery. Lower the searchlight into the holes, then slide the searchlight towards the connector end of the batteryuntil searchlight locks in place.
Connect the Power Cord by attaching the cord’s female end of to the searchlight’s 4-pin power connector and attaching the cord’s male end to the battery connector. To lock, rotate only the locking ring clockwise. All connections are keyed; never force connections.
To Turn Searchlight On, press the red ON/OFF SWITCH. Searchlight starts on high power, holds setting for 2 seconds, then drops to normal power.
To Adjust Beam Width, pull the black 4-WAY SWITCH back to increase beam width to flood. Push the 4-way switch forward to decrease beam width to spot.
To Activate Strobe, rock and hold the 4-way switch to the left. The default setting is momentary strobe, which means that the searchlight will strobe when the 4-way switch is held to the left. Please consult the Operation Manual for instructions on how to program the left button function to continuous strobe or low beam mode.
To Activate High Beam, rock and hold the 4-way switch to the right. The default setting is momentary high beam, which means that the searchlight will stay on high beam when the 4-way switch is held to the right. Please consult the Operation Manual for instructions on how to program the right button function to continuous high beam mode.
To Attach a Filter, line up the three tabs on the filter with the slots on the front of the searchlight. Place filter over front of searchlight and turn filter counter-clockwise until fully seated. Filter will lock in place. Visit the Filters page to view available filter options.
The Maxa Beam Searchlight’s default switch settings can be modified with simple programming sequences. Customizable switch settings include setting the right and left button functions to “continuous” high and strobe, setting the default beam width, setting spot and flood limits, and changing the frequency of the searchlight’s strobe. Please consult the Operation Manual for programming instructions.
ANSI Risk Group 3. Warning. Visible and infrared radiation emitted from this searchlight. Permanent eye damage can result. Avoid direct exposure to the beam.
Do not look directly into the searchlight beam. Exposure of the eye to either the direct searchlight beam or a beam reflected from a flat mirror-like surface can cause permanent eye injury to the unprotected eye. Follow the same precaution even when an Infrared Filter is installed on the searchlight.